MCS 4-WAY Adjustable Reservoir Dampers

Adjustment Instructions MCS 4-Way Dampers

Beginning settings and how to adjust low and high speed compression and rebound and gas pressure on your MCS 4-Way adjustable reservoir dampers.

Beginning settings

Front and rear:

|  Low Speed Compression="5"     High Speed Compression="6"    
|  Low Speed Rebound="4"     High Speed Rebound="8"       
|  Reservoir Pressure="12 Bar (175 psi)"

Click values are counted from 0 (fully soft).

General information

  • The dampers are charged with nitrogen gas. Front and rear dampers are factory charged to 12 bar (175 psi). Always set or check pressure with a proper shock inflation tool, with the shock fully extended and cooled off.
  • Minimum pressure is 6 bar (85 psi). Maximum pressure is 18 bar (260 psi).
  • If your dampers use a Quick Disconnect, release the pressure before opening the dry-break coupling. After installing the damper, reconnect the coupling and re-pressurize to 12 bar (175 psi).
  • Do not use impact tools to install pin mount top nuts.
  • The 8 mm brass hex nut at the top of the damper is the rebound adjuster. Do not use it to hold the shaft while installing the first top nut. Install the first top nut onto your mount and snug it with a wrench or socket, then cinch it with a quick jerking motion or a tap from a plastic hammer. This is more than enough to secure the shaft to the top mount. Install the second nut and tighten it against the first. Holding the first top nut with a tappet wrench (thin wrench) makes this easier.
  • When fitting the rebound adjuster knob onto the 8 mm brass hex nut, make sure it clears all body components.

Adjustment instructions

MCS 4-Way adjustable dampers are independently adjustable in low and high speed rebound (extension) and in low and high speed bump (compression).

‍

Compression adjusters

The Low Speed Compression (LSC) and High Speed Compression (HSC) adjusters are on top of the remote reservoir. The LSC is the small knob on top; the HSC is the large knob.

  • LSC range: 10 positions (9 clicks). 0 = softest, 10 = stiffest.
  • HSC range: 19 positions (18 clicks). 0 = softest, 18 = stiffest.
  • Clockwise (−) softens compression damping.
  • Counter-clockwise (+) stiffens compression damping.

When fitting the damper for the first time, set LSC to 5 clicks from 0 and HSC to 6 clicks from 0. Turn each knob clockwise until it stops, backing off slightly if needed so it settles into a detent. This is the “0” position. From here, turn the LSC knob counter-clockwise 5 clicks and the HSC knob counter-clockwise 6 clicks.

The LSC knob turns with the HSC knob relative to the canister body and stays indexed to it. This is correct and does not change the LSC setting, so you do not need to hold the LSC knob while turning the HSC knob.

‍

Rebound adjustment

The rebound adjuster sits at the top of the piston rod. With the knob in the upper position it adjusts low speed rebound (LSR); in the lower position it adjusts high speed rebound (HSR). The release button in the center of the knob releases it from the lower position to the upper position.

  • Knob up: low speed rebound (LSR). 11 positions (10 clicks), 0 = softest, 10 = stiffest.
  • Knob down: high speed rebound (HSR). 19 positions (18 clicks), 0 = softest, 18 = stiffest.
  • Clockwise (−) softens rebound (extension) damping.
  • Counter-clockwise (+) stiffens rebound (extension) damping.

‍

High speed rebound

When fitting the damper for the first time, set HSR to 8 clicks from 0. Press the knob down to the lower position, then turn it clockwise until it stops, backing off slightly if needed so it settles into a detent.

Once it stops turning, DO NOT force it any further. This is the “0” position. From here, turn the knob counter-clockwise 8 clicks. High speed rebound is now set.

Low speed rebound

Press the center release button to bring the knob up from the lower (HSR) position to the upper (LSR) position. Set LSR to 4 clicks from 0: turn the knob clockwise until it stops, backing off slightly if needed so it settles into a detent.

Once it stops turning, DO NOT force it any further. This is the “0” position. From here, turn the knob counter-clockwise 4 clicks. Low speed rebound is now set.

Need help?

Call us toll free on 866-391-1091 or on 770-220-7940, or email info@motioncontrolsuspension.com.

Download the instructions

Get the full instructions as a PDF to keep with your dampers or print for the workshop.

See other instructions

Compare
1WNR

A single adjustable damper that over delivers.

See Instructions
Compare
2WNR

A unique double-adjustable damper with a feel all its own.

See Instructions
Compare
2WR

Remote reservoir performance with large blow off valves for stronger high speed control and improved compliance.

See Instructions
Compare
3WR

Builds off the 2WR with added low speed compression bleed to fine tune how driver inputs load the tires.

See Instructions